Views: 102 Author: Site Editor Publish Time: 2020-09-21 Origin: Site
What are the similarities between polyurethane and ordinary epoxy resin products? Both can enhance the compressive and tensile strength of the cement floor or the floor and drainage ditch against corrosion by strong acid and alkali chemical solvents. Below, Hitop Machinery will specifically talk about the respective characteristics of these two products!
1. Both have good tensile resistance, no cracking, no falling off and other properties;
2. Both have strong acid resistance. Corrosion properties of alkali salts and various oils;
3. Both have the properties of dustproof, waterproof, surface wear resistance, heavy pressure resistance, and impact resistance;
4. The former topcoat is suitable for outdoor use, while the latter is suitable for indoor use; while the biggest weakness or shortcoming of the latter is that it is afraid of strong ultraviolet radiation, which will cause yellowing under strong ultraviolet radiation, that is, fade, but it will not
Decomposition also affects the use; however, the former is much improved in terms of weather resistance compared with the latter, especially the yellowing time of the former is much longer than the latter, so the former is often used for outdoor construction requirements.
In the above introduction, are you aware of the reasons why polyurethane raw materials are often used for exterior walls? For more information on polyurethane, please continue to pay attention to Hitop Machinery.(https://www.chinapumach.com/)
Polyurethane elastomers are typical multi-block copolymers, where the molecular chain consists of flexible chain segments with a glass transition temperature below room temperature and rigid chain segments with a glass transition temperature above room temperature. The oligomer polyol constitutes th
Cold storage spray polyurethane focuses on the overall seamless condition after spray foaming. Polyurethane has good density, insulation and cold resistance. It is basically a closed cell structure. It not only has excellent thermal insulation properties, but also has good resistance to freezing and
In order to select the shrinkage rate of large cast polyurethane elastomer products more accurately, the influences of process conditions, environmental factors and product structure on the shrinkage rate were systematically investigated, and the change curves of shrinkage rate with time were measur
On June 8, the CNMC-A25 polyurea spraying machine produced by Hightop Group was loaded in Hightop Group Industrial Park and will be exported to Italy. CNMC-A25 polyurea spraying machine is widely used in industrial maintenance, tunnel, subway, roadbed waterproofing, foam film and television props pr
On May 27th, the CNMC-E3 polyurethane spraying machine produced by Hightop Group was loaded in Wente Industrial Park and will be exported to the Italy. CNMC-E3 polyurethane spraying machine is widely used in industrial maintenance, tunnel, subway, roadbed waterproofing, foam film and television pro
On August 2, CNMC-E3 polyurethane spraying machine was loaded in the industrial park and will be exported to France soon.CNMC-E3 polyurethane spraying machine is widely used in industrial maintenance, tunnel, subway, waterproofing of road base, production of foam film and television props, pipeline
For the polyurea spraying equipment should take how to recommend1, polyurea is a set of waterproof, anticorrosion, wear-resistant, protection of multiple performance materials, but there is a certain range of tolerance, polyurea's recommended temperature range for the use of -40 ℃ -120 ℃.2、 Polyurea
Polyurea waterproof and anti-corrosion construction is generally spraying operation, in front of the small series to tell you why the reason for spraying, I believe everyone should have understood, now is about the construction process of the problem, let's take a look at it.Summary of polyurea wate
One. Corrosion resistanceIn addition to hydrogen acid, concentrated nitric acid and some strong oxidants, polyurea coatings show good stability in acid, alkali, salt, seawater, oil and other media, in the salt spray medium to do a strengthening comparative experiment, 1000 hours later, polyurea and
1. Increase efficiencyThere's a reason operators don't like manual mixing. It's a repetitive, physically demanding, and inefficient job. This includes manual heating and mixing of elements, trying to guess the correct dosage and loading the mixed paint into the spray system. It's becoming increasing